Major General 2024 Talon 1000R-4 Build Thread

[Mopower58]

Skids don’t take up any additional space toward wheel than standard trailing arm

I was referring to trailing arm clearance.

 

[Admin]

 

[Coeus]

I was referring to trailing arm clearance.

Ah… yea it looks close and hard to get the right angle to show it…

 

[Plumber32]

Thanks … scratches mostly on the lower outside edge or bottom?

Mostly on the highest bar on the rear. It really does it's job pivoting through tight woods rolling off trees. I don't even avoid using them on purpose either.

 

[Coeus]

Drilled out a hole through SuperATV stiffener to attach the front skid plate

 

[Coeus]

Attached 2 out of 3 self-tappers for trailing arm guards… the tire cribs are in the way so I’ll attach those later

 

[Coeus]

Next up is to lower it so I can work on interior items…. Remaining 4-points, windshields, electronics, etc…

 

[Coeus]

Might have a problem with rubbing here between the frame stiffener and the a-arm guards… anyone run into this issue?

 

[NTCPrezJB]

Might have a problem with rubbing here between the frame stiffener and the a-arm guards… anyone run into this issue?

View attachment 428331View attachment 428332

Grab the Jack and you’ll find out pretty quickly. Dremel can shave down the A arm guard easily enough though.

 

[Coeus]

Grab the Jack and you’ll find out pretty quickly. Dremel can shave down the A arm guard easily enough though.

It was very close on full extension so probably take them back off to cut of a portion and drill drainage holes

 

[Mopower58]

Next up is to lower it so I can work on interior items…. Remaining 4-points, windshields, electronics, etc…

Ole evil eye @Backwoods might help on your 4 points! 🤣

 

[Phantomhunter1]

Might have a problem with rubbing here between the frame stiffener and the a-arm guards… anyone run into this issue?

View attachment 428331View attachment 428332

Grab the Jack and you’ll find out pretty quickly. Dremel can shave down the A arm guard easily enough though.

I had that problem on my P1k as well. The frame stiffened was very close. I did exactly as mentioned. Just used a cut off wheel and cut a arm guard back so I had about 1/2" clearance.

 

[Coeus]

I had that problem on my P1k as well. The frame stiffened was very close. I did exactly as mentioned. Just used a cut off wheel and cut an arm guard back so I had about 1/2" clearance.

Awesome! That sounds about right… might have to cut some off that back wing area as well

 

[Coeus]

Ole evil eye @Backwoods might help on your 4 points! 🤣

Take it to the dealership?

 

[Mopower58]

Take it to the dealership?

Only if you want to bust a nut. There’s this Honda guy from Birmingham……………

 

[906UP]

It was very close on full extension so probably take them back off to cut of a portion and drill drainage holes

Get some arched A-arms, then the arm skids won't fit.....problem solved

 

[Coeus]

Get some arched A-arms, then the arm skids won't fit.....problem solved

Troof, but Current ones from SuperATV don’t work with LV

 

[906UP]

Troof, but Current ones from SuperATV don’t work with LV

Haha....seriously @SuperATV ???? They're no different from a non-LV R that I'm aware of, just need to be '22 or 23 & up

 

[Coeus]

Haha....seriously @SuperATV ???? They're no different from a non-LV R that I'm aware of, just need to be '22 or 23 & up

Something about the turning sensor… link on post 2

 

[Scoop]

Something about the turning sensor… link on post 2

Here's the post: Tire sizes on 2023 r2

 

[906UP]

Weird but OK, I can be dumb the rest of the day now 😆