Adam490's 1000R Live Valve Build and Shenanigans

[Adam490]

 

[Admin]

 

[Todd627]

View attachment 313573

Badass lookin' rig Adam 👍

 

[popeye]

JAH!

 

[Vondy]

s***box II looking good! Needs some trail stripes.

 

[Adam490]

s***box II looking good! Needs some trail stripes.

You don't have to tell me.... Jonesin over here

 

[Adam490]

JAH!

Yep, just an old s***box. Can't believe yours still works!

 

[Adam490]

@Jelewis80 let me know when you want to get some scratches on the top of that grocery getter.

 

[J80]

@Jelewis80 let me know when you want to get some scratches on the top of that grocery getter.

You better get a locker put in if ya want to keep up with that grocery getter 🤣🤣

 

[Adam490]

Got the 10-80 Dirtsports Snorkel kit installed over the weekend. Used the same 3" Spectre filter and filter-wears outer that I've been running on the Pioneer for quite a while now. Hopefully I have the same performance out of this one on the Talon.

 

[GlockMeister]

Good looking rig bud!

 

[Adam490]

Good looking rig bud!

Thanks Bearded Wonder!

 

[Adam490]

 

[highpocket74]

Got the 10-80 Dirtsports Snorkel kit installed over the weekend. Used the same 3" Spectre filter and filter-wears outer that I've been running on the Pioneer for quite a while now. Hopefully I have the same performance out of this one on the Talon.

View attachment 313931

View attachment 313932

Thanks for the input Adam! Your buggy looks sharp but does need some "trail stripes". After I looked at my cover plate and shook it around a little, the extra 2 push rivets are not needed. The plate is stout enough to shake the whole machine with only the two factory screws installed! I thought 2 more anchors would be needed but they are not. The plates coming out of the shop will not have these holes. I'll revise the template also.

 

[Adam490]

Thanks for the input Adam! Your buggy looks sharp but does need some "trail stripes". After I looked at my cover plate and shook it around a little, the extra 2 push rivets are not needed. The plate is stout enough to shake the whole machine with only the two factory screws installed! I thought 2 more anchors would be needed but they are not. The plates coming out of the shop will not have these holes. I'll revise the template also.

Thanks, hopefully I'll get a chance to get those trail stripes later in Feb 😁

Ha, I did the same thing . Got it mounted up and could rock the entire machine so I didn't worry about the push rivets.

 

[CID]

Thanks, hopefully I'll get a chance to get those trail stripes later in Feb 😁

Ha, I did the same thing . Got it mounted up and could rock the entire machine so I didn't worry about the push rivets.

FEBRUARY!!! that's at least 2 weeks away?!?! 😭

 

[Adam490]

FEBRUARY!!! that's at least 2 weeks away?!?! 😭

I know, stupid job ... Won't be until the end of February at that!

 

[Vondy]

Making any more progress on the Talon?

 

[Adam490]

Making any more progress on the Talon?

Yeah, got my tablet mounted and started laying out where I want to run wiring. Been going back and forth on a dual battery setup and pulled the trigger yesterday. Trying to keep this one simple....

 

[Neohio]

~snip~
View attachment 316106

Crap! I've been out of it so long, I didn't even know these existed!
Well, got one on the way.

 

[BWAF]

Yeah, got my tablet mounted and started laying out where I want to run wiring. Been going back and forth on a dual battery setup and pulled the trigger yesterday. Trying to keep this one simple....

View attachment 316104
View attachment 316105

View attachment 316106

View attachment 316107

Looking good !!!