P1000 Todd's Mod thread

[Tramguage1]

Is the bar in front of the head rest? If So will it mount behind it?

 

[Admin]

 

[ToddACimer]

Is the bar in front of the head rest? If So will it mount behind it?

The bar is in front of the headrest but it's behind the back rest of the seat so I don't think you'll notice the bar being there at all. I'll have to ride it to know for sure. I may end of moving the head rests forward

The bar is a 2014-2017 RZR-4 rear harness bar
https://www.bikebandit.com/aftermar...races/dragonfire-harness-bar/p/59823?m=158889

 

[ToddACimer]

I just wanted to provide a little direction on the belt installation. The bolts for the seat belts are 7/16 fine thread. I didn't want to mess with tearing apart the stock belts so I made my own bolts also.

Shorter bolts

Nylon washers and steel washers similar to stock

Installed

Here's a few photos of the belts on and tube installed.

 

[ToddACimer]

I've since ordered the harness bar from Brickcity Fab to replace mine with a lower 1 piece bar. It's not here yet and it wasn't available when I started the 4 point install.


I also ordered 1" rear wheel spacers from SuperATV.

Pics before rear spacers

No spacer

Spacer added. Nuts torqued to 80ft-lb and red locktite

After

Not sure it will make any difference other than looks and it looks better

 

[elkguide]

Sure does look better.

 

[my99svt]

After I’d did my spacers, I noticed I definitely needed mud busters!


Sent from my iPhone using Tapatalk

 

[ToddACimer]

After I’d did my spacers, I noticed I definitely needed mud busters!


Sent from my iPhone using Tapatalk

The tire tread isn't outside the body so I think it'll be ok. I'm also not afraid of getting dirty.

 

[OnTheJob]

The tire tread isn't outside the body so I think it'll be ok. I'm also not afraid of getting dirty.

View attachment 63973

That's what those nets were for! Collecting mud. Never knew.

 

[my99svt]

I have offset wheels as well. They stick out more than factory.


Sent from my iPhone using Tapatalk

 

[OnTheJob]

I have offset wheels as well. They stick out more than factory.


Sent from my iPhone using Tapatalk

I use to think the nets were there to keep things in the buggy but I now realize it's to keep s*** hitting people in the buggy. I took them off because I gotta get in and out 100x a use.

 

[ToddACimer]

I have offset wheels as well. They stick out more than factory.


Sent from my iPhone using Tapatalk

As much as I rub the sides down trees, I think I'd just lose the mudbusters in the woods. At least the tires will help keep the trees off the body now

 

[elkguide]

The tire tread isn't outside the body so I think it'll be ok. I'm also not afraid of getting dirty.

View attachment 63973

That is an AWESOME "MUD CAMO" you've got there.

 

[ToddACimer]

Now that BCF makes a 1 piece bolt in bar, I swapped out mine for a bit more head clearance on the bar. I do think the previous height was better but the BCF bar is further from your head and neck.

 

[elkguide]

Now that BCF makes a 1 piece bolt in bar, I swapped out mine for a bit more head clearance on the bar. I do think the previous height was better but the BCF bar is further from your head and neck.

View attachment 65641 View attachment 65640

Not the "HEAD BANGING" type?

 

[ToddACimer]

Not the "HEAD BANGING" type?

I didn't have an issue head banging on the other one but this won't require relocating the headrest right away. I may still move the headrest forward 1/2-3/4"

 

[Kilo427]

I am gonna move my headrest slightly forward got some nylon round end cut offs to space it up some. At least until I get bucket seats in.

 

[ToddACimer]

I am gonna move my headrest slightly forward got some nylon round end cut offs to space it up some. At least until I get bucket seats in.

I spaced mine out with 1" OD tube and it was really floppy. The headrest really needs support across the metal frame it mounts to. I may get some 3/8" thick rubber and cut it to shape.

 

[ToddACimer]

I've been needing a real rear bumper and I came across a 48" ATV bumper which I thought would make good protection for the exhaust and center of the machine. The bumper is a Moose 0530-0309

Hung on the back of the machine for mock up. I want the bumper to tuck under the bed and not limit the bed dump.

Bumper clamped in place to get ideas for a mount

The mount tube I came up with for the bumper. Ties into the rear ROPS

Bumper mounted

Upper mount bolted in place with bed clearance

Next step will be the lower mount

 

[elkguide]

Great idea.

 

[ToddACimer]

Bumper is finished

Mounts

Installed before paint

All done.