Just checked mine! All hardware is tight, no slack or any movement that I can find. I'm not really sure what to look for either?
DG Rider
Member: Triple Clutch Club
Lifetime Member
Glock21user
" Nothing succeeds like excess "
Lifetime Member
It says only affects certain 2020s, is there a vin # range or cutoff or just have to wait to see if we get the letter? I think ours is a late 2020 if that matters.
Thanks for keeping us informed on this.
Recall for a damaged (improperly installed) bolt. Not enough info here to really know what's going on. The shafts are splined, the B joints aren't--they compress onto the splines. It seems the issue is a stripped bolt, resulting in a loose B joint connection, that can result in loss of steering control. Lowest B-joint only. Something is not conveying......
Hondasxs
Club Founder
Staff member
Lifetime Member
Supporting Member
It does when you consider the assembly line.
The steering shaft with the whole dash assembly is most likely set onto the frame.
The rack would already be installed and that connection point would of been someone's job.
Could of been wrong bolts, wrong toqure, or just a bad employee.
DG Rider
Member: Triple Clutch Club
Lifetime Member
So went and checked mine, and yes...there is some tiny damage to the bolt.
It's hard to tell from the pic, but it's there...trust me.
It looks like what happened is that the groove in the splined shaft didn't get aligned with the bolt hole properly. Bolt 1 and 2 have a "fixed" hole, while 3 has basically a flat side for some length of the shaft, with the ends returning to normal shaft shape. The ideal is to let 1 and 2 be tightened, while 3 can float and let the other 2 settle where they may. That's why it gets tightened last. Perhaps #3 was tightened 1st or some other out-of-order sequence, which ultimately forced #1 out of position a bit, and the impact tool forced it in. This damaged the bolt a bit.
Thing is, even after i aligned them, the #1 bolt will not tighten by hand as instructed in the video. My guess is that the pinch clamp gets distorted a bit when this misalignment happens, which may be hondas real concern. Mine appears fine, but steering stuff isn't anything to jack around with when you drive along shelf roads next to deep canyons. So i'm going to replace it. Yes...me!
The joint is about $100, with the bolts and washers being a buck or 2 each. It'd honestly cost me $40 in gas easily to get it to my nearest dealer, and I'd GLADLY pay the $60 extra to NOT have the guys at the dealer work on it.
If you're thinking the same, better get on it, as the parts might get thin. Strangely, while RMATV does have the joint for $112, the bolts are apparently on back order. Good news is, these parts are also used on autos, so i ordered them from a car parts place. I'll let you know if they are on back order.
Parts:
53323-SW5-003 Joint B (1)
90135-SB0-003 Bolt, steering yoke (3)
90511-671-003 Lock washer (3)
It's hard to tell from the pic, but it's there...trust me.
It looks like what happened is that the groove in the splined shaft didn't get aligned with the bolt hole properly. Bolt 1 and 2 have a "fixed" hole, while 3 has basically a flat side for some length of the shaft, with the ends returning to normal shaft shape. The ideal is to let 1 and 2 be tightened, while 3 can float and let the other 2 settle where they may. That's why it gets tightened last. Perhaps #3 was tightened 1st or some other out-of-order sequence, which ultimately forced #1 out of position a bit, and the impact tool forced it in. This damaged the bolt a bit.
Thing is, even after i aligned them, the #1 bolt will not tighten by hand as instructed in the video. My guess is that the pinch clamp gets distorted a bit when this misalignment happens, which may be hondas real concern. Mine appears fine, but steering stuff isn't anything to jack around with when you drive along shelf roads next to deep canyons. So i'm going to replace it. Yes...me!
The joint is about $100, with the bolts and washers being a buck or 2 each. It'd honestly cost me $40 in gas easily to get it to my nearest dealer, and I'd GLADLY pay the $60 extra to NOT have the guys at the dealer work on it.
If you're thinking the same, better get on it, as the parts might get thin. Strangely, while RMATV does have the joint for $112, the bolts are apparently on back order. Good news is, these parts are also used on autos, so i ordered them from a car parts place. I'll let you know if they are on back order.
Parts:
53323-SW5-003 Joint B (1)
90135-SB0-003 Bolt, steering yoke (3)
90511-671-003 Lock washer (3)
Last edited:
DG Rider
Member: Triple Clutch Club
Lifetime Member
This is the video in the notice...
Special thanks to @HondaTech for being the man and getting this to us.
Special thanks to @HondaTech for being the man and getting this to us.
I had the same thought about fixing it myself rather than taking it to a dealer. I haven't taken mine apart to inspect yet but I did order the bolt and washer just incase. With only 103 miles on it, I hope there's no damage yet.
How many miles are on yours to cause the pictured damage?
advertisement
DG Rider
Member: Triple Clutch Club
Lifetime Member
I think the damage was done at assembly at the factory. Nothing was loose. Mine has 89 miles.
Got a call from the dealership last week.
They want to do the recall. They offered free pickup if I pay them for the first service.
I couldn't help but wonder if they are reimbursed by Honda for pickup costs.
They want to do the recall. They offered free pickup if I pay them for the first service.
I couldn't help but wonder if they are reimbursed by Honda for pickup costs.
Smitty335
Well-Known Member
Lifetime Member
Supporting Member
I really doubt Honda pays the dealer for pick up and delivery, think your dealer is trying to take care of you.
B
Yep it is there. The first bolt in the video above barely even has a spot on it and they say it is damaged.
The they show 3 more with more damage. I wonder if the bolts were manufactured out of tolerence? If they were a few thousandths to small they might let movement happen which starts wear.
B
You guys might want to watch this video. The first bolt that they say is damaged has a very small spot on it and they say it is damaged.
Perfect bolt... probably ok. Any funky specs or spots, ridges or rings....not OK.
DG Rider
Member: Triple Clutch Club
Lifetime Member
I don't think it has anything to do with the bolts themselves being manufactured wrong. I think the damaged bolt is an indicator of improper assembly. On mine, the small groove in the steering shaft was misaligned with the hole. Not radically...but enough that the splines got boogered a touch and let the bolt get damaged.
It seems like maybe #3 in the video got tightened 1st, which forced #1 slightly out of position, but still had enough to let whatever impact tool get it started and run it home, which marred the bolt and deformed the clamp a bit. I'm sure @HondaTech will have more on this...
Last edited:
TxDoc
Well-Known Member
Lifetime Member
B
advertisement
Similar threads
