P1000 2022 Honda 1000 new features

[HondaTech]

The knuckle part number is different. I'll have the check tie rod taper and diameter tomorrow since I know the nut is a change.

I thought they went to the smaller stem like the Talon?

 

[Admin]

 

[ToddACimer]

I thought they went to the smaller stem like the Talon?

They did go to the 10mm stem the new joint minimum OD on the taper is about .5mm smaller than the old joints which allows it to seat further in the knuckle. Oddly enough I had a spare (bent) knuckle to test fit tonight since we started this conversation. I torqued the new joint into my knuckle and it seats nice and deep in the taper. It also leaves a good witness marker around the diameter of the taper up to the full knuckle thickness, about 18mm

Here's a photo of the joint after being torqued but with the nut backed off. Still bummed Honda didn't give us a castle nut.

So what I learned is the taper appears to be the same but is likely a bit longer for better/deeper engagement in the knuckle and the stem/stud is smaller. This makes me feel better about this working. Cleaning the knuckle and new joint and doing a dye test would be more precise but that's assuming my 2500mile used knuckle is perfect too.

Next check will be tie rod clearance vs SuperATV arms at full cramp. Since the guys running heim joints clear, I should be ok.

 

[StewB]

Please tell me they fixed the undersized cupholders?

 

[Hondasxs]

Please tell me they fixed the undersized cupholders?

Yes, In exchange you lose the LED headlights.

 

[bumperm]

Yes, In exchange you lose the LED headlights.

(Shaking head) . . . I wonder why they would have done that? That makes so little sense that it's baffling.

 

[helopilot]

I like the previous front end look better. Looked more rugged. Maybe it's just the added color matching around the lights and under the grille. Maybe in time it'll grow on me.

I wonder how the aftermarket bumpers will effect cooling on the new model? Also hoping the SwitchPros RCR-Force-12 will fit on that dash.

 

[Tmorg]

I have a feeling 2022 parts are going to be popular.

Out with the old, in with the new.

Old mess
View attachment 328713

2022 parts installed in a 2018

View attachment 328714

Did this make any difference at all on the heat??

 

[ToddACimer]

Did this make any difference at all on the heat??

Not sure yet. It's only 30 degrees here.

 

[Tmorg]

Not sure yet. It's only 30 degrees here.

My bad! Sorry us florida boys don't think about that stuff!! It's 85 here today! I also seen one of your other post right after I replied to this one about your next ride coming up would be the test/tuning session.

 

[zfisher]

I did some parts checking on the 2022, 49 state and the california models, both use the same under seat pans, so if they fit the 18 model it will fit up to 21 california models also with evap. Hope this helps

thanks for looking that up....you did all the hard work haha

 

[kandt]

Didn't want to start a new thread- but a random question about the 2022 1000/1000-5 models.

The large switches in the deluxe are not wired but installed ready for low amp accessories. The Trail/Forest models have some wired with decals on the switches.

Anyone know if the switches with decals are etched or are they stick on decals? I know they are not backlit but was wondering if decals are available that could be used to indicate the various uses? (Too much time I guess while waiting on arrival of the Pioneer )

 

[bumperm]

Can't help so much, but on my '21 SE, there were three switch plugs wired back to the fuse box behind the "lower" switch panel. No switches for these accessory plugs. IIRC, one was wiper and I can't remember the others. They had stick-on labels. I abandoned them in place, as I was adding a second battery and fuse block for accessories, w/ no plans for wiper/washer etc.