P1000 2022 Honda 1000 new features

[zfisher]

I`m just like everyone on here and interested to see if these panels will fit older models as well, another hoop to throw in the ring is that I have a California model. So I'm interested to see if it will work with the evap system that comes on my model....p.s was not happy to find out I had a California model......

 

[Admin]

 

[ToddACimer]

Take a picture with nothing under the seat or a California model. They likely fit with some adjustments

 

[vbk]

I did some parts checking on the 2022, 49 state and the california models, both use the same under seat pans, so if they fit the 18 model it will fit up to 21 california models also with evap. Hope this helps

 

[Bighat]

Somebody said these were on backorder?

Honda must have allocated them to the Hondasxs top fansView attachment 328549

Don't understand how that's going to fix the problem. Band aid. It's going to take professional grade, thick, heat reflective insulation. When I get time to fix my 21 I'll post it. That may help some with the air gap, but not a fix. That had some Hot A?? engineer test it and she was already hot. She may have been blonde too.

 

[Todd627]

Don't understand how that's going to fix the problem. Band aid. It's going to take professional grade, thick, heat reflective insulation. When I get time to fix my 21 I'll post it. That may help some with the air gap, but not a fix. That had some Hot A?? engineer test it and she was already hot. She may have been blonde too.

This is what you need...

Quick Shield

 

[trigger]

Don't understand how that's going to fix the problem. Band aid. It's going to take professional grade, thick, heat reflective insulation. When I get time to fix my 21 I'll post it. That may help some with the air gap, but not a fix. That had some Hot A?? engineer test it and she was already hot. She may have been blonde too.

Like one piece of thick rubber that goes from the front of the seat all the way up the back and seals all the holes between the cab and engine compartments. Custom fit to the contours and cab lines allowing for dump bed operation, access for maintenance and without interfering with any safety items. All black, can be easily cleaned and isn't effected by mud, water or UV rays. Can be installed in a P1 in about 20 mins with no push pins or adhesives. Put it in and forget it.
Now that would be a fix! 🤔

 

[trigger]

This is what you need...

Quick Shield

Been trying to spread the word without being totally obnoxious. Thanks Todd!

 

[Bighat]

This is what you need...

Quick Shield

Do you use this? And it works?

 

[Todd627]

Do you use this? And it works?

Had one in my P500. Worked fantastic. @trigger has sold tons of these to the P500 group and now has expanded to other models. Any questions don't hesitate to PM him.

 

[ToddACimer]

My 2022 tie rods came in today. Honda has already updated the parts manual to make these replacements for all the 2016-2021 machines and they are beefy with the exception of the smaller m10 but on the taper but they improved the nut to have a much larger flange. Pics and part numbers attached.

The new tie rods are 3 pieces and the inner tie rod link is now an M16 vs the old m14.

 

[HondaTech]

They haven't been superseded for '16-'21 models.

 

[ToddACimer]

They haven't been superseded for '16-'21 models.

I agree with you after looking it up on Rocky Mountain but when we looked it up at the dealer they were the same and we couldn't find the old parts list.

 

[HondaTech]

I agree with you after looking it up on Rocky Mountain but when we looked it up at the dealer they were the same and we couldn't find the old parts list.

If their using our dealer parts fiche it should be pretty easy. But not all dealers are equal.

 

[Hondasxs]

If their using our dealer parts fiche it should be pretty easy. But not all dealers are equal.

I don't think they would go back and update old fish with new (different) parts.
Being the 3 piece vs 2 piece.
That would lead lots of confusion.

But hey.. who knows.


Sent from my SM-G996U using Tapatalk

 

[HondaTech]

I don't think they would go back and update old fish with new (different) parts.
Being the 3 piece vs 2 piece.
That would lead lots of confusion.

But hey.. who knows.


Sent from my SM-G996U using Tapatalk

They could supersede the parts to the new number, and keep the same picture. They've done weirder stuff.

 

[ToddACimer]

They could supersede the parts to the new number, and keep the same picture. They've done weirder stuff.

That's what it looked like happened when I was at the dealer. We paged through 2016, 2018 and 2020 and the all matched 22. But looking online today it's still different 2016-2021 vs 2022.

 

[Hondasxs]

They could supersede the parts to the new number, and keep the same picture. They've done weirder stuff.

it's a totally new design.

Not like it's just a new part number, which is usually a manufacture change or something small.

Sent from my SM-G996U using Tapatalk

 

[HondaTech]

it's a totally new design.

Not like it's just a new part number, which is usually a manufacture change or something small.

Sent from my SM-G996U using Tapatalk

They do it with power equipment all the time, carburetor design changes and the part you get looks like it doesnt belong on what your working on.

 

[HondaTech]

That's what it looked like happened when I was at the dealer. We paged through 2016, 2018 and 2020 and the all matched 22. But looking online today it's still different 2016-2021 vs 2022.

If their using the dealer parta fiche, double clicking on the part # it will show every machine it fits.

The 22 parts "dont" fit the older 1000s.

 

[ToddACimer]

If their using the dealer parta fiche, double clicking on the part # it will show every machine it fits.

The 22 parts "dont" fit the older 1000s.

The knuckle part number is different. I'll have the check tie rod taper and diameter tomorrow since I know the nut is a change.