P1000m5 Windrock1000- She’s still sexy!

[Windrock1000]

Are you sure?

The new one I got for the right front one is. I don’t know about the rear ones didn’t take it out!

 

[Admin]

 

[GlockMeister]

They make an over the axle bearing greaser... @Ragnar406 has one

 

[Ragnar406]

They make an over the axle bearing greaser... @Ragnar406 has one

Honda Pioneer 1000 Over Axle Wheel Bearing Greaser Tool grease 40mm ab25-1728 | eBay

Here is the one I bought- seems to work well I have been on one ride since I used it.

 

[Windrock1000]

Honda Pioneer 1000 Over Axle Wheel Bearing Greaser Tool grease 40mm ab25-1728 | eBay

Here is the one I bought- seems to work well I have been on one ride since I used it.

I got one from someone on Facebook and it works good too.

 

[BWAF]

Bearing is sealed. Have to grease inside out.

Is there two bearings I thought in between bearings may half to pull inner shields out haven't been in mine yet hope it's a while .Did a friend's rhino here a while back it had two worked well

Sent from my SM-G930U using Tapatalk

 

[Windrock1000]

Is there two bearings I thought in between bearings may half to pull inner shields out haven't been in mine yet hope it's a while .Did a friend's rhino here a while back it had two worked well

Sent from my SM-G930U using Tapatalk

Only one split bearing. Solid outer race and 2 inter split races. The little greaser puts grease in between the races.

 

[BWAF]

Only one split bearing. Solid outer race and 2 inter split races. The little greaser puts grease in between the races.

Oh that changes things a lot

Sent from my SM-G930U using Tapatalk

 

[joeymt33]

View attachment 82908 View attachment 82909 View attachment 82910 View attachment 82911 New mod for those with older machines.

Looks good David! I did this a while back as I’ve had to change the bushings twice now. I did cut a groove in the bushing in three sides to allow grease to enter the bearing surface and get to the outside cup seal.

It’s so satisfying to use these knowing that I am prolonging the life.

 

[Windrock1000]

Looks good David! I did this a while back as I’ve had to change the bushings twice now. I did cut a groove in the bushing in three sides to allow grease to enter the bearing surface and get to the outside cup seal.

It’s so satisfying to use these knowing that I am prolonging the life.

Thought about grooving but there is not a lot of meat on the bone

 

[joeymt33]

Thought about grooving but there is not a lot of meat on the bone

There’s not much there but I grooved the metal sleeve not the plastic one and it was very shallow. I’ll probably should have did driver side different from the passenger side and see which one last longest.

 

[Windrock1000]

Honda Engineering could have done a lot better here!

 

[JTW]

View attachment 83557 Honda Engineering could have done a lot better here!

That’s pretty piss poor!

 

[Plumber32]

View attachment 83557 Honda Engineering could have done a lot better here!

I'm assuming you felt something loose and went to investigate ?

 

[Windrock1000]

I'm assuming you felt something loose and went to investigate ?

I wish. Upper a-arm (front) mounting tabs. Superatv bushings and inter sleeve seized on bolt. Bolt became piviot point. Bolt cut 20% in too. Get grease in arms boys and girls. I thought the bushings where wore out not so. Bolt was tight.

 

[Windrock1000]

Little cutting, welding, and drilling and she will be a lot stronger!

 

[BWAF]

Little cutting, welding, and drilling and she will be a lot stronger!

Can't wait to see what you do !

Sent from my SM-G930U using Tapatalk

 

[Smitty335]

I wish. Upper a-arm (front) mounting tabs. Superatv bushings and inter sleeve seized on bolt. Bolt became piviot point. Bolt cut 20% in too. Get grease in arms boys and girls. I thought the bushings where wore out not so. Bolt was tight.

I packed the bushings and greased the bolts during assembly, hope this buys me some time!

 

[Plumber32]

I packed the bushings and greased the bolts during assembly, hope this buys me some time!

They are tough to get greese into. I've only been able to get it to take greese twice.

 

[Windrock1000]

I packed the bushings and greased the bolts during assembly, hope this buys me some time!

I did too 16 months ago.

 

[Smitty335]

I wish. Upper a-arm (front) mounting tabs. Superatv bushings and inter sleeve seized on bolt. Bolt became piviot point. Bolt cut 20% in too. Get grease in arms boys and girls. I thought the bushings where wore out not so. Bolt was tight.

I think Super ATV forgot to make a grease passage through the sleeve to the bolt. A grease zirt to no where, is what they have! Take the zirk out and drill a hole through the sleeve.