What did you do to/with your Talon today?

[CumminsPusher]

Went out on the property and cut trees out or the roads.View attachment 422458View attachment 422459

You have family out this way right?

 

[Admin]

 

[mmjsport]

I saw a thread of a guy asking about aftermarket axles on his 23 R. I tried to reply to the post but it got deleted I guess. But if you read this I had a similar issue with my 23R4 and the axle breaking.

I ended up breaking an axle a month ago or so on my 23R4. Slow speed crawling and it snapped from inside of the rear assembly. The dealer had to take the other side axle off to remove the broken side by pushing it out from inside the rear assembly. Dealer said they had never seen that before and have never had issues with Honda axles in the past. They all thought it could have been a manufacturing defect. They sent the picture to Honda and they covered it under warranty. Might help asking your dealer to submit a claim.

 

[Trey - 3DSXSDesign]

Copying ehart814's Pioneer 500 thread and DG Rider's Pioneer 700 thread - if you did something to (or with) your Talon and don't want to start a new thread for one or two posts, here's the place. Ideas, mods, best photos, stucks, recoveries 😳 - whutcha got?

Cigarette lighter accessories are the go-to for plug in electrics, we've all used them for most of our lives but they suck in a rougher environment, they keep unplugging themselves. When I was (much) younger, I'd cut the ends off and replace with a 1/8" phono plug, more secure and less bulky. There were three reasons I quit - 1. I got tired of it because I was always adding to my plug-in accessories. 2. A converted accessory wouldn't work in someone else's vehicle. 3. My first GPS had the step down circuitry from 12v to 5v in the plug, you couldn't cut it off.

The Talon's cig plug is key controlled, every time I stop, the GPS shuts off so I needed an always hot cig plug. When I got the replacement socket, it was so loose that the small spring in the end of plug would push it out, losing contact almost immediately. (no matter how I rotated the plug, there was no secure position)

This is what I came up with and although it looks like a 7 year old made it, 🤫 it works pretty well and I can plug/unplug it with one hand. It's far enough forward that it's water protected by the dash but not so far under that it's hard to reach. It's almost a foot in front of the passenger's knee (which I'll rarely have) so shouldn't be (too) dangerous. The circuit is controlled by a toggle switch so I can shut it off if necessary, like when washing.

Studs clamped for welding -
View attachment 211269

View attachment 211274

View attachment 211271

I'll probably have to make more of these depending on each cig plug, but it's just for the GPS for now. I always round my corners - 1. I won't gouge myself on them later. 2. It looks much better and only takes a minute on the bench grinder.

Another non Talon project -
View attachment 211413

Nylock nuts hold their position and are infinitely adjustable (and why the studs are a bit long).
View attachment 211272

View attachment 211273

I hooked my plug up to my 8 gang auxbeam so I could power it with the key off . Hard to explain but my auxbeam comes on with my key but I have a over ride with a switch to power it with key off , I had to use a diode to keep power from back feeding and powering up the ecu .

 

[kjbula1980]

I installed a CA Technologies pull plate. Very nice piece but was missing a washer.
This should add significant strength to the radius rod mounting area and a proper pull mount.

 

[Plumber32]

Nothing. Hoping it's still in my trailer.

 

[01Canes]

Traded it in 😬

 

[CID]

I've wondered what the actual tip angle is for the Talon R compared to the listed tilt table number of 37.3*. For the same reason that I ran it until it quit, wondering how far I could go on a full tank (with the plastic tube removed from the tank filler neck) -173 miles (8.75 gallons). That number is almost useless - I get from 7.9 mpg to almost 20 mpg, depending entirely on what I've ridden that day.

Short version - this needs to be done with two winches which will eliminate the weight of the come-along and chain (in this case). I'll do that first chance I get.

Speaking of useless numbers - this is the static tilt angle under perfect conditions. But when we're riding everything is dynamic, don't push yer luck.

The initial set up. I thought I needed the chain but didn't, should have unhooked it, but didn't. Its weight distorted the results.

Max tilt, chain and come-along hanging from the 'loose side' -

Winchin' provided by @WillyBill and his lovely Mrs.

Weight of chain and come-along affecting tilt limits - (again at max) -

At 10-1/2 lbs. rear and 9-1/2 front, the tires never rolled enough for the rims to touch.

We saw 54* but didn't get that photo - 😒 Bottom line, it takes way more angle than you'd think to put a Talon on its side.

Three friends all saw 35*, I'll try harder next time.

 

[JenElio]

Traded it in 😬

View attachment 426029

Had to turn my phone sideways to see the entire SXS......🤦‍♂️

 

[lowranger]

Heading to Nevada tomorrow to meet friends and do more exploring off Hwy 50 (loneliest Hwy). Old Pony Express station. I was there 2 years ago and just scratched the surface of all the country to explore. Will send pictures.

 

[lowranger]

Buffalo Summit 6,880 ft Nevada

 

[lowranger]

On our ride yesterday, found a good place for a burger and beer. We rode 92 miles.

 

[O2bsmitty]

I've wondered what the actual tip angle is for the Talon R compared to the listed tilt table number of 37.3*. For the same reason that I ran it until it quit, wondering how far I could go on a full tank (with the plastic tube removed from the tank filler neck) -173 miles (8.75 gallons). That number is almost useless - I get from 7.9 mpg to almost 20 mpg, depending entirely on what I've ridden that day.

Short version - this needs to be done with two winches which will eliminate the weight of the come-along and chain (in this case). I'll do that first chance I get.

Speaking of useless numbers - this is the static tilt angle under perfect conditions. But when we're riding everything is dynamic, don't push yer luck.

The initial set up. I thought I needed the chain but didn't, should have unhooked it, but didn't. Its weight distorted the results.
View attachment 426215

Max tilt, chain and come-along hanging from the 'loose side' -
View attachment 426216

Winchin' provided by @WillyBill and his lovely Mrs.
View attachment 426218

Weight of chain and come-along affecting tilt limits - (again at max) -
View attachment 426219

At 10-1/2 lbs. rear and 9-1/2 front, the tires never rolled enough for the rims to touch.
View attachment 426220


We saw 54* but didn't get that photo - 😒 Bottom line, it takes way more angle than you'd think to put a Talon on its side.

Three friends all saw 35*, I'll try harder next time.
View attachment 426226

I understand the chain weight effects it but still impressive.

 

[AMink]

On our ride yesterday, found a good place for a burger and beer. We rode 92 miles.View attachment 428640View attachment 428641

They make great burgers there! It doesn't look like much but don't let that fool you.

 

[AMink]

We spent the Memorial Day weekend (thank you to those who gave all!) north of Elko, Nevada, near Wildhorse Reservoir. Did some riding and general hanging out.

Nevada high country

We saw a few mule deer up this canyon. They saw us too and disappeared.

My buddy's sidewall patch finally said enough after over a year.

The Mormon crickets were out in force.

Nevada chair lift when the ski areas are closed.

Made some turns on some really nice snow up high.

 

[AMink]

just scratched the surface of all the country to explore

You could spend the rest of your life riding the roads and trails in Nevada. Thousands of miles on public land.

 

[lowranger]

We spent the Memorial Day weekend (thank you to those who gave all!) north of Elko, Nevada, near Wildhorse Reservoir. Did some riding and general hanging out.

View attachment 430650
Nevada high country

View attachment 430651
We saw a few mule deer up this canyon. They saw us too and disappeared.

View attachment 430652
My buddy's sidewall patch finally said enough after over a year.


View attachment 430653
The Mormon crickets were out in force.

View attachment 430654
Nevada chair lift when the ski areas are closed.

View attachment 430655
Made some turns on some really nice snow up high.

I like that Wild Horse area, use to do a lot of hunting up there in the mid 90s.
We planned on going back up there in June with the Talon and cruise around.

 

[AMink]

I like that Wild Horse area, use to do a lot of hunting up there in the mid 90s.
We planned on going back up there in June with the Talon and cruise around.

I took a horns shorter than ears antelope from there a few years ago. Amazing country!

 

[SLOWPOKE693]

Took it for a ride around the block earlier at 40-45mph and got called an azzhole by some random Kyle standing at his gate taking a picture/video so I smiled, waved and continued on my merry way back to the house. Maybe I'll take my tractor out in the morning and brush hog a track into my big field and run my Talon WFO all day. I live well outside city limits in the country and can do stuff like that on my property at will. Kyle should probably go back in the house and mind his business before I really give him something to whine about.

 

[GovtMule]

I drove @TimG ‘s. Needless to say I’m hooked!

 

[AMink]

Well, not today but a couple over the weekend. New springs are on. Don't believe them when they say it's a two hour job! Maybe if you have the cool spring compresser tool and a vice, or if you don't have to take the shock off several times to adjust to the correct ride height. I know you can do it on the machine but there just isn't a lot of room to work. I did survive the Harbor Freight compresser tool so there's that!