P1000m5 Traveller II

[sharp]

Locking mechanism screwed up.....

View attachment 113551

When in doubt, use a hammer and chainsaw.

 

[Admin]

 

[JACKAL]

I’m going to lower the differential to correct the CV angles. This should be fun.

View attachment 113534

Just asking because I don't know, won't that bugger the prop shaft angle? For every action is an equal and opposite reaction?

 

[JTW]

Well that’s a pisser!

 

[joeymt33]

Just asking because I don't know, won't that bugger the prop shaft angle? For every action is an equal and opposite reaction?

I figured I’d get somebody!

 

[JTW]

I figured I’d get somebody!

Surprise surprise!

 

[JACKAL]

I figured I’d get somebody!

Hey, they way yall fiddle with the machines geometry its like training day at FAC waterhead works for RAM design.

 

[joeymt33]

All is good. I just need to put the skid plate back on and make sure there are no leaks. Sounds like something I’ll do tomorrow.

 

[DGann]

As much as you tinker with the pioneer, it should be bulletproof bye now, Oh wait a minute, we got to remember who’s driving it!!!!!


Sent from my iPhone using Tapatalk

 

[Delton]

As much as you tinker with the pioneer, it should be bulletproof bye now, Oh wait a minute, we got to remember who’s driving it!!!!!


Sent from my iPhone using Tapatalk

Hey you leave him alone!! I personally benefit from all Joeys how to videos when he tears sh*t up lol.

 

[joeymt33]

In prep for the Takeover I didn’t have much to do but I did inspect a lot of things.

I pulled the IGR and clutches. They looked perfect.




I also changed the angle of the exhaust outlet on the HMF muffler. A lot of people complain because it points straight down and makes a lot of dust.

 

[joeymt33]

I got tired of the mud busters tearing off. I made some replacements out of rubber conveyor belt and they have already been tested thoroughly and have proven to be tougher than the plastic mud buster.



I cut some slits in it in several places to allow it to fold and not pull out the rivets and screws. I also scored the backside to allow it to fold easier.

 

[Smitty335]

I got tired of the mud busters tearing off. I made some replacements out of rubber conveyor belt and they have already been tested thoroughly and have proven to be tougher than the plastic mud buster.

View attachment 125136

I cut some slits in it in several places to allow it to fold and not pull out the rivets and screws. I also scored the backside to allow it to fold easier.

View attachment 125137

The exhaust mod will be welcome to people ridding behind you in dry conditions, HMF's make a lot of dust, you happen to make templates of your mud busters? I never bought the Mud Busters because, I knew they would last like a fart in a whirl wind.

 

[joeymt33]

The exhaust mod will be welcome to people ridding behind you in dry conditions, HMF's make a lot of dust, you happen to make templates of your mud busters? I never bought the Mud Busters because, I knew they would last like a fart in a whirl wind.

I did not but I can bring them to the takeover for anyone that wants to trace them out.

 

[Adam490]

@joeymt33 do you happen to have a link to the filter/clamp you're using on your snorkel? I was checking it out at Takeover and really like that clamp/filter setup you've got.

 

[joeymt33]

@joeymt33 do you happen to have a link to the filter/clamp you're using on your snorkel? I was checking it out at Takeover and really like that clamp/filter setup you've got.

The clamp was an old clamp I had laying around but I could probably find something like it. The filter should be in my Amazon history.

I’ll go check.

 

[joeymt33]

I did not remove the factory filter. I’m using this pre-filter just to save the factory filter and extend its life.

 

[Adam490]

View attachment 128153

View attachment 128154

I did not remove the factory filter. I’m using this pre-filter just to save the factory filter and extend its life.

That's what I figured. Any issues with rain/mud running that setup? I like the simplicity of running it out the hood and just buying another hood if I don't want it snorkeled any more. Thanks!!

 

[JTW]

I swap between snorkel heads depending on weather..

 

[joeymt33]

That's what I figured. Any issues with rain/mud running that setup? I like the simplicity of running it out the hood and just buying another hood if I don't want it snorkeled any more. Thanks!!

I carry the snorkel head to swap out in case of rain.

 

[Adam490]

Thanks guys!