![ToddACimer](/data/avatars/m/5/5905.jpg?1483301310)
I added the wfosxs SuperATV windshield extension today. Nice piece. Super high quality and works great
So far my 1x3 box tubing is holding up well.Starting on my 1200 mile service (1262)...
View attachment 209633
Whoops... Looks like we need some extra beef up in here. If somebody makes a crossmember that @Plumber32 and I cant smash in 500 miles, that would be 1 tough sum b****
I ordered the kit with the horn so it's wrapped in the same wire loom but the horn does connect directly to the battery and is not dead with the key,whereas the signals and 4 ways get their power from ignition under the dashOn that turn signal kit with horn, did it come with the horn all wired together with the signals or was it a separate loom that was wired separate?
I'd like to see chase video of the red strobe in a lot of dust for comparison. I had that same light in my cart before I found the small amber one I used; I like the way that one looks better than mine. I could only see @Hondasxs bright blue whips when we had 8 machines running fast through the dust and he was the lead vehicle while I was the caboose. I think anything mounted high will do the job just fine though.Chase light and overhead switches are installed.
The switch box is 3D printed from Crossroads 3d with 4 switches. The switches have high and low red, as well as reverse and strobe red.
View attachment 210130
Reverse just the LED up top
View attachment 210131
Top and bottom
View attachment 210134
High red and low red
View attachment 210132
View attachment 210133
Strobe has a cool flash pattern. I'd guess high red will be the one we use most.
This is the light
This is the switch panel, enclosure and mount
SXS Switch panel - Crossroads 3D
crossroads3d.com
Well the last 200 miles were a blast. Spent the weekend on Drummond Island Mi. Lots of rocks, deep water, mud and quite a bit of off trail private property exploration. It comes at a price though.
I lost 3 wheel center caps, tore 2 CV boots, bent a tie rod, bent 2 a-arms, broke a net buckle. We wrecked a steering rack on an Arctic Cat wild cat and tore 2 a-arms off a RZR1000 too. Whoops
Couple photos from the weekend.
RZR carnage, we pulled the a-arm, hammered on it a bit and re-welded it but it still looked terrible
View attachment 144650
Pioneer carnageView attachment 144651
Quick tie rod repair
View attachment 144652
View attachment 144653
Little bit off camber here
View attachment 144654
View attachment 144655
View attachment 144656
View attachment 144657
View attachment 144658
Are you a Michigander? Im south of Grand Rapids.
I’m about to Purchase a yellow P1k and am nervous about the rough terrain on Drummond?
We take a dirt bike trip every year in the UP for some single track trails and usually do Drummond too. Can be a B**** if there’s a lot of rain and deep roots!
Are you a Michigander? Im south of Grand Rapids.
I’m about to Purchase a yellow P1k and am nervous about the rough terrain on Drummond?
We take a dirt bike trip every year in the UP for some single track trails and usually do Drummond too. Can be a B**** if there’s a lot of rain and deep roots!
Do you have any supports for your outer rear skid plates? I am building a skid now, and was trying to decide how to mount the rear portion, or just cut it out? Thanks
View attachment 214980
View attachment 214978
Do you have any supports for your outer rear skid plates? I am building a skid now, and was trying to decide how to mount the rear portion, or just cut it out? Thanks
View attachment 214980
View attachment 214978
I did not add a support back there other than the formed flange in the UHMW. I have not had a time where I felt like that part was unsupported. It does collect a lot of dirt and I've been tempted to cut it off.