P1000 Forwards AArms and Shocks P1000

[TripleB]

I bought super atv arms, My budget for shocks is 700$. I’ll buy tires later. Thank you guys for your counsel. It’s been very helpful. I think I’m going to buy a full set of the shocks for 700$ It it’s good to be able to bounce stuff off of experienced guys. Btw, my pioneer with 28s got through Royal blue as good as any other machine I was with. Except for this. If you look close you can see my wife standing on the dash to keep her butt out of the mud. That’s on the trail to Town Rock.

View attachment 392731

That mudhole ain't doable in a Pioneer without
portals and at least 37s. KRX on 35s couldn't make it at the 2022 Takeover. Last fall at the MOM ride a Talon x4 on 35s couldn't make it either.

 

[Admin]

 

[TripleB]

I bought super atv arms, My budget for shocks is 700$. I’ll buy tires later. Thank you guys for your counsel. It’s been very helpful. I think I’m going to buy a full set of the shocks for 700$ It it’s good to be able to bounce stuff off of experienced guys. Btw, my pioneer with 28s got through Royal blue as good as any other machine I was with. Except for this. If you look close you can see my wife standing on the dash to keep her butt out of the mud. That’s on the trail to Town Rock.

View attachment 392731

That mudhole ain't doable in a Pioneer without
portals and at least 37s. KRX on 35s couldn't make it at the 2022 Takeover. Last fall at the MOM ride a Talon x4 on 35s couldn't make it either.

My bad, that's a different mudhole. The mudhole you're in, a talon x4 couldn't make it on 31s at this takeover lol.

 

[Scamih]

The only thing that stops my pioneer is when it bottoms out. Otherwise it feels unstoppable. I see the draw for more lift for more clearance but there is a line between too tall and

My bad, that's a different mudhole. The mudhole you're in, a talon x4 couldn't make it on 31s at this takeover lol.

View attachment 392817

A razor with 35s made it through the deep grooves on the right side but not down the middle. I was trying to creep around the edge on the left. Bad decision.

 

[GovtMule]

My bad, that's a different mudhole. The mudhole you're in, a talon x4 couldn't make it on 31s at this takeover lol.

View attachment 392817

Looks like he Parked but didn’t Wreck! (See what I did there!)

 

[Remington]

A POO POO FIRE TRAP RZR with 35s made it through the deep grooves on the right side but not down the middle. I was trying to creep around the edge on the left. Bad decision.

Fixed it for ya!

Hes lucky pushing it that hard (NoHomo) there wasnt a great big 🔥

 

[Todd627]

Looks like he Parked but didn’t Wreck! (See what I did there!)

And you thought that you weren’t worthy of posting outside the NTC tonight. Well played 👍🏼

 

[Robobrainiac]

Here is a recent rough country post in case you missed it.

P1000 - My thoughts on the Rough Country shocks (for what it's worth)

After having my Pioneer 1000-5 for almost 4 years and doing a fair amount of upgrading, I became even more frustrated with the suspension - most notably the front. The suspension was never "good" with the factory shocks on a deluxe model, but after adding the heavy JEI bumper, extra battery...

hondasxs.com

 

[Scamih]

Here is a recent rough country post in case you missed it.

P1000 - My thoughts on the Rough Country shocks (for what it's worth)

After having my Pioneer 1000-5 for almost 4 years and doing a fair amount of upgrading, I became even more frustrated with the suspension - most notably the front. The suspension was never "good" with the factory shocks on a deluxe model, but after adding the heavy JEI bumper, extra battery...

hondasxs.com

Thank you. I ended up just ordering 2 like the guy did in this post for the front so I could put them on when I put the arms on. I’m hoping I can maintain the same height with new shocks. I’ll send picks and review it once I get them installed. New front SuperAtv arms, new front rough country shocks, new brake pads while I have it apart. I haven’t orederd new 30 inch tires yet. My 28x10x14 tusk aramid terrabites have very little wear on them. I’m trying to sale them before I order new ones.

 

[chucksmith0706]

Looking forward to a review on the shocks.


Sent from my iPhone using Tapatalk

 

[Scoop]

Thank you. I ended up just ordering 2 like the guy did in this post for the front so I could put them on when I put the arms on. I’m hoping I can maintain the same height with new shocks. I’ll send picks and review it once I get them installed. New front SuperAtv arms, new front rough country shocks, new brake pads while I have it apart.

Sounds like a plan!

I haven’t orederd new 30 inch tires yet. My 28x10x14 tusk aramid terrabites have very little wear on them. I’m trying to sale them before I order new ones.

Nothing wrong with those tires ... Just use 'em up!

 

[Scamih]

I’m going to document changes for my own records: measured before A-arms and shocks, clearance to tire, measured distance from axle to ground at each end, measured ground to fender in center of wheel, checked level of floor board in center.

 

[Scoop]

if you measure from the ground to anything, make sure all your tires are properly inflated, and put the same tire back on each corner. Tire pressure/tire height will affect your measurements. For ride height change comparisons (before vs after), I typically measure from a point that doesn't change due to changes in tire height/pressure/size (e.g., from center of axle to fender).

 

[Scamih]

I rode it enough to know the shocks are a lot better. I hit a spot I usually bottom out on. I just put 2 shocks on the front used the preload settings as they came in box. Gave me 3/4 lift. I’m going to ride it like that for a while. Put new super atv arms on front gave me 1.5 more clearance to tires. So far I like it and I’ll update as I ride it more. I’m going to see if the shocks sag a little. Very happy with the purchase. I’ve got a set of arms to put on back. Install tips from a non- mechanic, buy a ball joint separator, pay attention to how to route the brake line as I screwed it up on the first side Use a nail set to drive cotter pins out if you can’t get to them, that worked pretty good. Super atv video doesn’t show torquing stuff down, I did based off post I saw on here. I appreciate you guys sharing tips along the way. Anyone in East Central Illinois want to buy a pair of tusk 10 ply with 1/2 tread 28x10x14. I’m looking for 300$. I want to upgrade to 30s but l can’t justify if I don’t sale these.

 

[Scamih]

It changed the angle on the axle a little which make sense.

 

[Scamih]

I adjusted rear factory shocks to level out machine. Worked good. Just need to ride it more to give good report. Level matches pretty close to what I had prechanges

 

[Scamih]

I adjusted rear factory shocks to level out machine. Worked good. Just need to ride it more to give good report. Level matches pretty close to what I had prechanges

This is what it looked like before read adjustment.

 

[packer58]

Dang ....you need to clean up your bubble

 

[Scoop]

Make sure tire pressures are the same and tire height is the same before you assume level.

 

[Scamih]

Dang ....you need to clean up your bubble

That’s my tree cutting level, keep it in with my saw

 

[packer58]

That’s my tree cutting level, keep it in with my saw

Ok, NOW you've got my attention ..... tell more about your tree cutting level ...