B
SLOWPOKE693
Well-Known Member
Supporting Member
Bolt on. I also hear that a YXZ quick release setup works as the splines on the column are the same as our Hondas.
B
Awesome, order from raceco yesterday. Thanks
SLOWPOKE693
Well-Known Member
Supporting Member
Nice!
One thing you note about splined quick releases though... The splines on the wheel will line up any way on the column and putting the wheel on crooked is easy. Best bet is to paint a couple splines and do the same to the quick release hub where the wheel lines up centered so its much easier to get on straight.
B
Did that when taking the hess qd out. Just waiting for the new one. Thanks
SLOWPOKE693
Well-Known Member
Supporting Member
Got the rear tires mounted on the new wheels along with the lexan mud covers I picked up and then pushed it outside so I could clean the garage. The garage was getting a wee bit out of control....
The carbon fiber hood looks killer out in the sun!
The carbon fiber hood looks killer out in the sun!
Last edited:
SLOWPOKE693
Well-Known Member
Supporting Member
Today's adventure is going to be pulling the sender out of the tank and swapping pumps. I gutted the stock sending unit when I switched to the Injector Dynamics return style fuel system and ID 1300 injectors last year but only installed a slightly bigger fuel pump. My Injector duty cycle was higher than I wanted it to be running E90 so I'm swapping the pump out for a larger unit to get that in check and have it flow enough volume in case I want to run methanol at a track that doesn't have a fuel rule....
With a bit of luck I'll get the tank and lines in tonight before I leave for my work trip in the morning so it will be one less thing I have to do when I get back later this week.
With a bit of luck I'll get the tank and lines in tonight before I leave for my work trip in the morning so it will be one less thing I have to do when I get back later this week.
Last edited:
SLOWPOKE693
Well-Known Member
Supporting Member
Fuel pump is in, fuel tank is back in, fuel lines are re routed to a cooler location and the floors are back in.
Moving the battery and wiring to the passenger compartment really cleaned up the back of the frame on the passenger side. There used to be a crap load of stuff there and now it's empty.
Moving the battery and wiring to the passenger compartment really cleaned up the back of the frame on the passenger side. There used to be a crap load of stuff there and now it's empty.
SLOWPOKE693
Well-Known Member
Supporting Member
Front diff clutch delete is almost finished. My guy says I'll have it by the end of the week. 
As soon as it's in my hands I'll be able to install it, take measurements and then have The Driveshaft Shop build me a carbon fiber driveshaft. Zoom-zoom 😁
As soon as it's in my hands I'll be able to install it, take measurements and then have The Driveshaft Shop build me a carbon fiber driveshaft. Zoom-zoom 😁
P1K5Dave
Well-Known Member
Lifetime Member
Club Contributor
Man @SLOWPOKE693 - That's a lot of upgrades for this year. You're going to be taking names!
advertisement
SLOWPOKE693
Well-Known Member
Supporting Member
I hope so. I've about had it with getting beat by RS-1's so I'm doing everything I can to stop that from happening this year.
SLOWPOKE693
Well-Known Member
Supporting Member
So this will be full-time 4wd with an unmodified front diff?
Sent from my Pixel 7 Pro using Tapatalk
SLOWPOKE693
Well-Known Member
Supporting Member
SLOWPOKE693
Well-Known Member
Supporting Member
Car is wired, brakes are bled. Going to go pick up some Mobil 1 4T racing oil shortly and warm it up so I can change the oil and filters.......
SLOWPOKE693
Well-Known Member
Supporting Member
It's alive! Let it come up to temp and then changed the oil and filters. While I was working on the engine I threw in a fresh set of Brisk spark plugs.....
I forgot to clean and re oil the air filters so I'll have to do that sometime this week after work.
I forgot to clean and re oil the air filters so I'll have to do that sometime this week after work.
SLOWPOKE693
Well-Known Member
Supporting Member
After the maintenance stuff was out of the way I bolted in the seat and the new Team Tech harness and got the belts adjusted. I still need to put all my gear on to finalize the seat belt adjustments but it's pretty close now.
Before I cleaned up and went in the house for the evening I bolted the new window net on too.
Before I cleaned up and went in the house for the evening I bolted the new window net on too.
SLOWPOKE693
Well-Known Member
Supporting Member
Pay no attention to the dirt all over the seat. I laid on the garage floor twice to adjust the belts and didn't realize what I was doing to the seat until the second go around.... Doh!! 😆
SLOWPOKE693
Well-Known Member
Supporting Member
Race schedule for memorial day weekend has been posted...... Ya buddy!
BrianN
Ditch rider
Supporting Member
Is this for motorcycles also? Define the classes for the illiterate. Also how many races are there in the season?
advertisement
