P1000 parts interest

[jak9922]

out of curiosity what parts would you guys be intersted in for the 1k that are not available yet

 

[Admin]

 

[Hondasxs]

Grab bar.
Harness bar.
Chain saw mount.

 

[jak9922]

Grab bar.
Harness bar.
Chain saw mount.

grab bar would that be for the passenger side or also for the middle seat

 

[Hondasxs]

Idk..
I did just the passenger on mine.
But now I need something for my 3y old daughter. It also needs to be removable when she is not in there.

 

[lrandy129]

Glass full-tip-out front windshield.

 

[jak9922]

Glass full-tip-out front windshield.

saftey glass can be very expensive

 

[lrandy129]

Yep, they're ~$1,000 on the PoPo's, but spent almost half that on my poly tip out. I'd rather buy glass and be able to run a windshield wiper without sacrificing the tip out functionality of my poly. Honda's attempt at a tip is a good start, but doesn't let enough air through in hot weather.

Glass Tip-Out Windshield | Polaris RANGER

 

[ohanacreek]

Honda's attempt at a tip is a good start, but doesn't let enough air through in hot weather.

Glass Tip-Out Windshield | Polaris RANGER

View attachment 35504

Amen preach it brother

I wish it tipped out. Even if it were only 8-10" at the bottom.

 

[Smitty335]

Yep, they're ~$1,000 on the PoPo's, but spent almost half that on my poly tip out. I'd rather buy glass and be able to run a windshield wiper without sacrificing the tip out functionality of my poly. Honda's attempt at a tip is a good start, but doesn't let enough air through in hot weather.

Glass Tip-Out Windshield | Polaris RANGER

View attachment 35504

This would last me like a fart in a whrill wind! HA!

 

[popeye]

out of curiosity what parts would you guys be intersted in for the 1k that are not available yet

Rock sliders that are high and tight to the plastic. That offer protection but wont be an anchoring point on the first obstacle

Sent from my LGMS631 using Tapatalk

 

[Smitty335]

Rock sliders that are high and tight to the plastic. That offer protection but wont be an anchoring point on the first obstacle

Sent from my LGMS631 using Tapatalk

Non electric heat shield is on the top of my list

 

[popeye]

A-arm protection for the super atv arched arms.

Sent from my LGMS631 using Tapatalk

 

[JTW]

Everybody has really nailed it!!!

 

[Eltobgi]

The one thing I still haven't seen is a 2" front receiver hitch for the front for the P1K. It may be that the front bumper is too thin to support it

 

[Delton]

The one thing I still haven't seen is a 2" front receiver hitch for the front for the P1K. It may be that the front bumper is too thin to support it

Those stockers are really tough so it wouldn't surprise me if it held up. I've wanted to build a bolt on top winch mount and receiver for them. And rock sliders, grab bars, and harness mounts. Not enough hours in the day though. Maybe one day.....

 

[Peking_Duck]

Surprised no-one has mentioned heavy duty clutch packs.....no problems yet with mine but it would be nice to see some other options out there.

 

[sharp]

out of curiosity what parts would you guys be intersted in for the 1k that are not available yet

Rear spare tire carrier and rotopax mount for a P1k-3

 

[jak9922]

The one thing I still haven't seen is a 2" front receiver hitch for the front for the P1K. It may be that the front bumper is too thin to support it

i can definitely fix that problem

 

[Eltobgi]

i can definitely fix that problem

The design would have to be strong enough to pull a fully loaded P1K5 out of 3-4 ft of mud! Look forward to seeing what you come up with!

 

[jak9922]

Saturday morning a guy is supose to drop off a 1k for me to work on