P500 Need Help - Light Bar Install

[futzin]

I bought a 12" lite bar (36 volt) that did not come with a switch, which of course I'll need to buy.

It has two short wires supplied. Utilizing the Honda harness, what else do I need (wires) and a crude diagram for this electrical noob would be greatly appreciated!

 

[Admin]

 

[Buggyman]

I bought a 12" lite bar (36 volt) that did not come with a switch, which of course I'll need to buy.

It has two short wires supplied. Utilizing the Honda harness, what else do I need (wires) and a crude diagram for this electrical noob would be greatly appreciated!

no expert by any means but fwiw mine came with wire heavy enough for the length of run based on max amps, inline fuse ,relay ,switch. one of the wizards will help with a diagram

 

[futzin]

Hoping I don't need all that jazz! 😆

 

[Hib]

Everything you need in a kit. I've used a couple of these:

https://www.amazon.com/Nilight-10014W-Harness-Waterproof-Warranty/dp/B074GWMRGD/?tag=sxsweb24-20

 

[trigger]

https://www.amazon.com/MICTUNING-Light-Wiring-Harness-Switch/dp/B00EZ9Y33W?tag=sxsweb24-20

 

[futzin]

So a run from light to switch to harness is a no-go?

 

[Hondasxs]

So a run from light to switch to harness is a no-go?

That would be fine. Adding in a 10 amp fuse.

Most don't like this because it is directly wired. But it's fine for small draw items.

Sent from my SM-G996U using Tapatalk

 

[Hondasxs]

That would be fine. Adding in a 10 amp fuse.

Most don't like this because it is directly wired. But it's fine for small draw items.

Sent from my SM-G996U using Tapatalk

Assuming you mean 36 watts... not volts.
If the package says 36 watts. Then a 5 amp fuse is what you should use.

Sent from my SM-G996U using Tapatalk

 

[futzin]

Assuming you mean 36 watts... not volts.
If the package says 36 watts. Then a 5 amp fuse is what you should use.

Sent from my SM-G996U using Tapatalk

72 watts, 36 volts. per the specs . . .

 

[Hondasxs]

72 watts, 36 volts. per the specs . . .

Still unclear..

Does it say MAX 36 volts.
Because your system is 12 volts.

72 watts on 12v needs 10 amp fuse.

Sent from my SM-G996U using Tapatalk

 

[futzin]

Auxbeam LED Light Bar 12" 72W Driving Light with 3W 24pcs Chips Combo Beam Waterproof​

tem Dimensions LxWxH	16.14 x 3.94 x 3.94 inches
Brand	Auxbeam
Color	12inch combo
Vehicle Service Type	Passenger Car, Bus, SUV, Truck
Voltage	32 Volts
Light Source Type	LED
Position	Front Outside
Material	Aluminum
Water Resistance Level	Waterproof
Remote Control Included?	No

 

[futzin]

Power: 72W

Number of Chips: 24pcs*3w high intensity LEDs

Operating Voltage: DC 9-32V

Luminous Flux: 5040lm~7200lm

Beam Type: 30 degree (spot beam) & 60 degree (flood beam) combo

Color Temperature: Pure White 6000K

Waterproof Rate: IP67

Working temperature: -40~85 degree centigrade

Dimension (with bracket): approx. 302*106*64mm/11.89*4.17*2.52inch

Material: Black Diecast aluminum housing, PC lens

Mounting Bracket: Stainless steel bottom bracket

Above 30,000 hours life time

Certified by CE & ROHs

 

[Hondasxs]

Operating Voltage: DC 9-32V

Ok. Its 32v max.. Just making sure it will work with 12v.
One guy I dealt with bought a 24v only light. I never seen one like that. It was actually for some industrial equipment. He was SOL.

Sent from my SM-G996U using Tapatalk

 

[futzin]

Thanks!

 

[futzin]

Done. Seems to work correctly and nothing went 'zzzt!'

 

[Hondasxs]

Done. Seems to work correctly and nothing went 'zzzt!'

I don't see anything.

Sent from my SM-G996U using Tapatalk

 

[futzin]

 

[Hondasxs]

Kool. I see it now. Lol

Sent from my SM-G996U using Tapatalk

 

[futzin]