P1000 Looking for Wheels in all the Wrong Places

[Olive]

Yes it won’t rub as long as your tires are 28” or smaller.

You're the best! Thanks for helping me.

 

[Admin]

 

[Olive]

Those should fit just fine, website might say no because the P1K is actually a 4/136 bolt pattern not 4/137. But they fit, lots of guys run 4/137 👍

I sincerely appreciate your help! You saved me tons of time and a lot of headache.

 

[PJon]

One final question:
I found these and am ready to pull the trigger.

• ITP Delta Steel Wheel (Front / 14X7 4/137 4+3) (Black) Compatible with 11-19 CAN-AM COM1000XT

As far as you know, I have found the correct wheel, even though the website says that it will not fit my vehicle when I put in Honda Pioneer 1000-5. Correct?

I run 14" 5-2 all the way around and have no rubbing. A day or two ago I responded to someone else on the forum who was having problems with his 14" 5-2's with 28" tires. He stated that that the dealer installed them with 1" spacers and he had severe rubbing. When you run a 14" 4-3 offset, during a turn, the outer edge of the tire will be closer to the body due to geometry.

 

[Olive2016]

IMPORTANT NOTE: I purchased the ITP Delta Steel Wheels that I mentioned in my post above. THEY DID NOT FIT. The bolt pattern was acceptable, but THE BOLT HOLES WERE WAY TOO SMALL. The Honda lugs did not fit through the holes.

I thought about drilling out the holes to accommodate the larger Honda lugs, but the center hole in the wheel was too close to the lug holes and that would have left just a sliver of metal between the lug holes and the large center hole.

So, the moral of the story is that the ITP Delta Steel Wheel 14X7 that says Compatable with 11-19 CAN-AM COM1000XT will not fit a Honda Pioneer 1000.

Still looking for wheels in all the wrong places.

 

[Olive2016]

OK..... Found these on Ebay: I.T.P. Delta Steel Wheels 14X7 4/137 4+3 12MM 1422319014B. The fitment chart shows that they will fit a Honda 1000-5. I will let everyone know if they do.

 

[Olive2016]

Fit perfectly!
If you are looking to put new shoes on your Honda 1000-5 but don't want to have to do a lift kit or to use spacers, here's what I did and it worked perfectly:
From Ebay:

From Amazon:

This combo works perfectly!
No longer looking for wheels in all the wrong places!

 

[TripleB]

Fit perfectly!
If you are looking to put new shoes on your Honda 1000-5 but don't want to have to do a lift kit or to use spacers, here's what I did and it worked perfectly:
From Ebay:
View attachment 260815

From Amazon:
View attachment 260816

This combo works perfectly!
No longer looking for wheels in all the wrong places!

How wide is your machine in the front and rear now?

 

[Sr56]

Fit perfectly!
If you are looking to put new shoes on your Honda 1000-5 but don't want to have to do a lift kit or to use spacers, here's what I did and it worked perfectly:
From Ebay:
View attachment 260815

From Amazon:
View attachment 260816

This combo works perfectly!
No longer looking for wheels in all the wrong places!

@Olive -please post a picture when you have them mounted.


Sent from my iPad using Tapatalk

 

[Olive2016]

How wide is your machine in the front and rear now?

65" front and back

 

[TripleB]

65" front and back

No spacers in the rear?

 

[Olive]

No spacers in the rear?

Nope. No spacers at all.

 

[TripleB]

Nope. No spacers at all.

My 3 seater with 4 front wheels(same off set) and 28x10x12 blackwater evos on all 4 wheels is 1 inch more narrow in the rear.

 

[Olive]

SR56: As requested. Here is a before and after

 

[PJon]

SR56: As requested. Here is a before and after View attachment 261795

Looks great. Those should do a lot better than the originals.

 

[Sr56]

Thanks for the pic. I like the look !


Sent from my iPad using Tapatalk