P1000 I want a 1000-5 rear ROPS & Roof on 1000-3

[Johnny_C]

I just measured the outside of the of the black
plastic in line with the bottom of the tail lights
and it's 61.25" I guess the factory ROPS will not
fit the 1k3... I'll see if I can verify that through
Honda, but it sounds like it's a custom job if I
want it done.

Thanks!

John

 

[Admin]

 

[Whiskey1]

I just measured the outside of the of the black
plastic in line with the bottom of the tail lights
and it's 61.25" I guess the factory ROPS will not
fit the 1k3... I'll see if I can verify that through
Honda, but it sounds like it's a custom job if I
want it done.

Thanks!

John

John - I took a few more measurements this am. My P1K5 measures 57 inches wide at the same location you mention above. I hadn't realized there was a difference. Thanks for the info!

 

[Johnny_C]

I am now at the point of designing a rear
structure to cover the bed area, and tie
into the ROPS. The design will be pretty
simple to get fabbed up, but I have to find
someone to make the top. I intend to make
it easily removable. I need to find someone
who make the canvas portion. Zippers, tie
downs, Velcro, and vinyl windows. Good
enough to match the factory canvas.

I haven't found anyone local, yet.

Something shaped like the back of
a Tow equipped Hummvee. (I can't
embed images from work, apparently).



John

 

[HondaTech]

As far as bolting up, the 3 seat has all the bolt holes for mounting a 5 seat cage. As for the bed being bigger and stopping it from fitting I can't attest to that. If you could find a lower section that bolts to the back frame that would be the tell all to see if it would clear the bed sides.

 

[CashMoney]

If you want to run the plastic honda top there should be no problem for someone with a tube bender to make that one work. I believe you might even be able to make honda's clamps work with a little sanding, which that may not even be necessary. Look for a 4wheel drive jeep type shop those guys build roll cages all the time. Even a race car shop. They even have tub clamps that slide in the tube and weld and bolt together so you could remove the rear section if you wanted too easily.

 

[pct]

If you deside to use the honda back half and widen it I will sell you mine widening the stock one would be less work
i'm in WV make me an offer if you are interested
Paul

 

[Tundra20]

Ok i know this is a old post but im curious i want to put the rops on my 18p1000 -3 has anything changed since 16 or do i need to go ahead have one made as i want to get a good place for the spare to mount thanks for ur replies in advance

 

[Dezrik]

The 1000-3 bed is too wide for the 1000-5 Rear ROPS, I wanted to do the same because i HATE The rear seats of the -5 and want a 3 Seater bed.

Ok i know this is a old post but im curious i want to put the rops on my 18p1000 -3 has anything changed since 16 or do i need to go ahead have one made as i want to get a good place for the spare to mount thanks for ur replies in advance

 

[Tundra20]

Ok thank you for info i will see bout getting one made

 

[GlockMeister]

Ok i know this is a old post but im curious i want to put the rops on my 18p1000 -3 has anything changed since 16 or do i need to go ahead have one made as i want to get a good place for the spare to mount thanks for ur replies in advance

I found this by accident yesterday....
Honda Pioneer 1000 Back Seat and Roll Cage Kits | UTV Accessories

 

[Dezrik]

I found this by accident yesterday....
Honda Pioneer 1000 Back Seat and Roll Cage Kits | UTV Accessories

Suprisingly I did too for some reason, Saw a ad for it LOL