Talon Bouncy Throttle

[PRF]

I have trouble holding steady with gas pedal on slow rocky trails. Has anyone found a fix or a tip to help prevent the bucking bronco syndrome!

 

[Admin]

 

[Lovetorque]

I have trouble holding steady with gas pedal on slow rocky trails. Has anyone found a fix or a tip to help prevent the bucking bronco syndrome!

Heel on the floor side of foot against center firewall with pressure becomes natural after a bit

 

[PRF]

Heel on the floor side of foot against center firewall with pressure becomes natural after a bit

Thanks for reply.

I have tried to adapt as you described, does not seem to be getting any easier with time. I dont think better foot control will be the answer for me. I have driven many different machines over this type of terrain without this much throttle bucking. Other forums like the Jeep forum suggest heavier throttle spring but I cannot find a good place to add one.

 

[sharp]

I have trouble holding steady with gas pedal on slow rocky trails. Has anyone found a fix or a tip to help prevent the bucking bronco syndrome!

If its anything like the pioneer, its part of the learning curve. Your foot has to get trained and use to it. It wont take long. Although ive never used one, I think some people use a throttle max to help. Keep riding!

 

[Lovetorque]

Thanks for reply.

I have tried to adapt as you described, does not seem to be getting any easier with time. I dont think better foot control will be the answer for me. I have driven many different machines over this type of terrain without this much throttle bucking. Other forums like the Jeep forum suggest heavier throttle spring but I cannot find a good place to add one.

I can break it in for you,fill the tank I’ll be right over

 

[DRKnight]

I added a heel support to steady my foot.
Cut a piece of 1 X 2 lumber, 3" long , cut a 45 degree angle across the face and secured it to the floor with two screws.
Works great.

 

[Smitty335]

I added a heel support to steady my foot.
Cut a piece of 1 X 2 lumber, 3" long , cut a 45 degree angle across the face and secured it to the floor with two screws.
Works great.

I've always thought that would work, now we need to make some out of poloyer!

 

[Lovetorque]

I've always thought that would work, now we need to make some out of poloyer!

Duck tape bailing wire and wood screws are what I use on my $25000 toy

 

[Tramguage1]

 

[Lovetorque]

View attachment 130047

You guys just need to drive more and hack less

 

[PRF]

View attachment 130047

I like it! Well done. Thanks.

 

[Tramguage1]

I like it! Well done. Thanks.

Its temporary until ThrottleMaxx has there product ready. Love the one on my Pioneer.

 

[TripleB]

View attachment 130047

For s***s and giggles what size hinge is that and would the same size hinge fit the pioneer 1000? I've got the throttle maxx on my pioneer and I love it. My buddy is too cheap to buy 1 and wants to go your route.

 

[ohanacreek]

For s***s and giggles what size hinge is that and would the same size hinge fit the pioneer 1000? I've got the throttle maxx on my pioneer and I love it. My buddy is too cheap to buy 1 and wants to go your route.

@Delton

 

[Tramguage1]

For s***s and giggles what size hinge is that and would the same size hinge fit the pioneer 1000? I've got the throttle maxx on my pioneer and I love it. My buddy is too cheap to buy 1 and wants to go your route.

Yes and I will have to measure it. I got this one at HD or Lowes. I think it was the largest the carried. You could use same size for Pioneer.

 

[Delton]

8" gate hinge from Tractor Supply. Cut off part of the top then cut 1/2" split down middle. I had measurements wrote down at one time but can't find them now.

 

[Tramguage1]

8" gate hinge from Tractor Supply. Cut off part of the top then cut 1/2" split down middle. I had measurements wrote down at one time but can't find them now.

The Talon gas peddle is a little different. The slot needs to be offset to the left a little.the piece I cut off the left side was welded to the right side to make a spot for the bolt holes.

 

[Smitty335]

The Talon gas peddle is a little different. The slot needs to be offset to the left a little.the piece I cut off the left side was welded to the right side to make a spot for the bolt holes.

And after all this time after seeing your hinge, I thought you Texans were just hinged differently! HA!

 

[Delton]

The Talon gas peddle is a little different. The slot needs to be offset to the left a little.the piece I cut off the left side was welded to the right side to make a spot for the bolt holes.

Still wouldnt be hard at all to make. So easy a democrat could do it lmao

 

[JimmyTalon]

...but would probably expect it to be provided without charge.