H
Sonhas anyone had a problem with SATV arms looking to see what I'm in for with these arms
Best advice is do a search upper right corner of screen. Should be lots of threads on this. 👍
Rayger143
Well-Known Member
Lifetime Member
Supporting Member
Remington
Fife! POIDH Enforcement Officer
Lifetime Member
Supporting Member
Welcome From Michigan.
what exactly are are u asking? Are there any known issues?
what exactly are are u asking? Are there any known issues?
I dare you to try to break or bend one....
If you can do it....I'll give you another one for free.
🤣 🤣 🤣
If you can do it....I'll give you another one for free.
🤣 🤣 🤣
Russ989
Land of the free because of the Brave! 🇺🇸
Lifetime Member
Supporting Member
Club Contributor
Sonhas anyone had a problem with SATV arms looking to see what I'm in for with these arms
You have a better shot of the a-arm tab ripping off the frame….. don’t ask me how I know.
Todd627
HondaSxS Club Stress Management Director
Lifetime Member
Supporting Member
I bet he will even throw in some stickers too 😜
Robobrainiac
Well-Known Member
Lifetime Member
Everyone loves the SATV arms. The only reason anyone uses anything else is because they want a different ride height like the arms with built in lift.
russknight
Well-Known Member
Lifetime Member
I have them on the front of my 1000-3. Other than the bushings not taking grease, I've had no issues, yet.
advertisement
This is a true...and a very good point. I'd also recommend the frame stiffener for all the Pio 1k's.
Honda Pioneer 1000 Frame Stiffener / Gusset Kit
Frame stiffener / Gusset Kit for the Honda Pioneer 1000 and 1000-5 from the experts at SuperATV. Ships free from SuperATV
www.superatv.com
L
LarryAmboy
Well-Known Member
This is a true...and a very good point. I'd also recommend the frame stiffener for all the Pio 1k's.
Honda Pioneer 1000 Frame Stiffener / Gusset Kit
Frame stiffener / Gusset Kit for the Honda Pioneer 1000 and 1000-5 from the experts at SuperATV. Ships free from SuperATV
How does it fit with some of the skid plates out there?
Sent from my iPhone using Tapatalk
russknight
Well-Known Member
Lifetime Member
This is a true...and a very good point. I'd also recommend the frame stiffener for all the Pio 1k's.
Honda Pioneer 1000 Frame Stiffener / Gusset Kit
Frame stiffener / Gusset Kit for the Honda Pioneer 1000 and 1000-5 from the experts at SuperATV. Ships free from SuperATV
Just ordered one.
russknight
Well-Known Member
Lifetime Member
Wow!!!! Just received shipping confirmation!!! That took a whopping 19 minutes!!!
Robobrainiac
Well-Known Member
Lifetime Member
How well does it fit with a SuperATV skid plate and Denali plow plate?This is a true...and a very good point. I'd also recommend the frame stiffener for all the Pio 1k's.
Honda Pioneer 1000 Frame Stiffener / Gusset Kit
Frame stiffener / Gusset Kit for the Honda Pioneer 1000 and 1000-5 from the experts at SuperATV. Ships free from SuperATV
With our skid plate...you'd just remove the piece under the A-arm tabs. We make it separate to remove if you get the frame stiffener. Not sure with others. If they are one piece...its pretty easy to just cut that section off under the A-arm tabs where it would mount. The stiffener will also work like a skid plate right there.
True story. The SuperATV arms work. I like the steering geometry better than stock and the height is perfect for 30" tires. If you don't run steering stops you may crush your brake lines with stock lines and 2016-2021 tie rods. With 2022 tie rods the brake lines are fine.
I had 2000 hard miles on my front uppers when I noticed they were starting to bow under the shocks. I had this same problem with OEM arms (bent 2 uppers and 5 lowers). SuperATV sent me 2 arms and some stickers and the beatings continue.
I will note, my frame is gusseted on the upper a-arm and the lower tabs if you're not upgrading the other parts the SuperATV parts probably won't fail and likely won't fail first.
I'd buy from them again in a heartbeat.
WagginTail
Well-Known Member
Lifetime Member
Club Contributor
Good info on the brake line. I relocated mine so they wouldn't get pinched. Didn't cost anything except a little time
you mention that your frame is gusseted... any pics? and was it a kit or custom? very interested in strengthening mine as the frame tabs just ripped out of my last P1K in a minor hit to a stump
The upgrades are in my build thread.
Post in thread 'Todd's 2018 Build' P1000 - Todd's 2018 Build
I now have 12mm upper a-arms bolts too
Post in thread 'Todd's 2018 Build' P1000 - Todd's 2018 Build
I now have 12mm upper a-arms bolts too
advertisement
